BMW P0023: Exhaust Camshaft Position Actuator Circuit/Open Bank 2 — Diagnosis and Repair

P0023 means Exhaust Camshaft Position Actuator Circuit/Open Bank 2. The DME records it when the DME detects an open or implausible electrical load at the bank 2 exhaust actuator; diagnosis must separate an electrical signal fault from a real system fault. Use OBDThink to preserve the recording module and freeze frame for P0023, then test bank 2 exhaust VANOS solenoid power and DME control circuit without guessing or swapping parts. What Does P0023 Mean? This standardized powertrain DTC concerns bank 2 exhaust VANOS solenoid power and DME control circuit. On BMW vehicles the exact test plan and component layout vary by engine, chassis and DME software, so verify the VIN in BMW service information. The decisive clue is not the code alone: the DME detects an open or implausible electrical load at the bank 2 exhaust actuator. Compare commanded behavior with the measured signal before condemning a component. Code: P0023 Definition: Exhaust Camshaft Position Actuator Circuit/Open Bank 2 Module: DME (gasoline) or DDE where applicable Key evidence: the DME detects an open or implausible electrical load at the bank 2 exhaust actuator Typical causes: a loose actuator connector, oil contamination, open solenoid coil, harness break, missing supply, or DME driver fault Severity: diagnose promptly Note: confirm engine and wiring variant by VIN First preserve the freeze frame. If the DME detects an open or implausible electrical load at the bank 2 exhaust actuator, inspect bank 2 exhaust VANOS solenoid power and DME control circuit and its supporting system in the same operating condition. Symptoms • Exhaust Camshaft Position Actuator Circuit/Open Bank 2 commonly appears with extended cranking, intermittent stalling, timing retard or cylinder-specific combustion roughness. • The freeze frame may show the fault while the DME detects an open or implausible electrical load at the bank 2 exhaust actuator, which is more useful than the warning lamp alone. • Target and actual values separate a persistent defect from an intermittent connector or harness interruption. • A companion fault from the same module may identify whether bank 2 exhaust VANOS solenoid power and DME control circuit is the cause or a consequence. Possible Causes Start with accessible circuit and connection checks, then prove the sensor or actuator, and leave expensive mechanical work until last. • Low cost: inspect the connector, terminal tension, contamination and the harness around bank 2 exhaust VANOS solenoid power and DME control circuit. • Low cost: check hoses, ducts, grounds, fuses and supply paths that directly affect bank 2 exhaust VANOS solenoid power and DME control circuit. • Medium cost: test the named sensor or actuator dynamically; the defining evidence is that the DME detects an open or implausible electrical load at the bank 2 exhaust actuator. • Medium cost: correct the system condition rather than masking it; likely branches include a loose actuator connector, oil contamination, open solenoid coil, harness break, missing supply, or DME driver fault. • High cost: only after circuit and mechanical evidence, consider control-unit repair or major mechanical work using VIN-specific BMW service data. Diagnosis Steps with OBDThink OBDThink is an independent BMW coding and diagnostic mobile app and is not affiliated with BMW AG. Available live data and freeze frame detail depend on the vehicle, adapter and module. • 1. Scan every control unit with OBDThink; save P0023, the recording DME, status, frequency and freeze frame before clearing anything. • 2. Reproduce the recorded operating condition safely and graph target versus actual values. Correlate engine-speed or cam/knock data with starting and load; inspect the named sensor, shielded harness and mechanical trigger. • 3. With ignition safely isolated where required, inspect and electrically test bank 2 exhaust VANOS solenoid power and DME control circuit; load-test power and ground rather than relying on continuity alone. • 4. Separate circuit from mechanism: manipulate the harness while monitoring data, then perform the relevant smoke, vacuum, pressure, airflow or waveform test. • 5. Confirm the repair by clearing the code, completing a cold start and controlled drive cycle, and rescanning all related modules. IF the DME detects an open or implausible electrical load at the bank 2 exhaust actuator AND wiring/load test fails -> repair the circuit ELSE IF command is correct but mechanism does not respond -> test bank 2 exhaust VANOS solenoid power and DME control circuit ELSE compare companion faults and BMW VIN-specific test plan THEN clear, drive, and rescan The fastest distinction is to watch the relevant command and actual value while testing bank 2 exhaust VANOS solenoid power and DME control circuit; a fixed signal and a responding mechanism point in different directions. Repair • P0023 — High cost: repair the pump, turbocharger, timing hardware, cylinder-head passage or DME only after VIN-specific testing rules out cheaper causes. • P0023 — Low cost: clean and secure the correct connector, repair chafed wiring, restore a fuse/ground, or replace a split hose only when testing proves it. • P0023 — Medium cost: replace the confirmed sensor, valve, relay or solenoid and perform any BMW service-data adaptation that genuinely applies. • P0023 — Medium cost: repair the verified airflow, vacuum, exhaust or fuel-delivery defect that caused the implausible reading. After repair, verify that the DME detects an open or implausible electrical load at the bank 2 exhaust actuator no longer occurs, readiness can complete, and P0023 does not return as pending or confirmed. Can You Drive with P0023? Avoid continued driving if stalling, hard starting, metallic noise or severe misfire occurs. Treat P0023 as measured evidence, not a parts order. A saved freeze frame, a target/actual comparison and a load-tested circuit usually reveal the least expensive correct repair.