BMW P0357: Ignition Coil G Primary/Secondary Circuit Malfunction — Diagnosis and Repair

P0357 means Ignition Coil G Primary/Secondary Circuit Malfunction. The DME records it when coil G does not produce the expected primary-current signature or cylinder contribution; diagnosis must prove the named circuit or mechanism before parts are replaced. Use OBDThink to preserve the recording module and freeze frame for P0357, then test ignition coil G primary feed, DME trigger line, plug well and secondary ignition components in the condition that set the fault. What Does P0357 Mean? This standardized powertrain DTC concerns ignition coil G primary feed, DME trigger line, plug well and secondary ignition components. BMW component location and test routing vary by engine, chassis and DME software; use the VIN-specific wiring diagram and service plan. The code is not a parts verdict. Its defining evidence is that coil G does not produce the expected primary-current signature or cylinder contribution, so compare command, actual response and electrical integrity in the same operating window. Code: P0357 Definition: Ignition Coil G Primary/Secondary Circuit Malfunction Module: DME (gasoline) or DDE where applicable Key evidence: coil G does not produce the expected primary-current signature or cylinder contribution Typical causes: a failed coil, carbon-tracked boot, fouled spark plug, connector damage, open or shorted trigger circuit, missing feed, or DME driver damage Severity: diagnose promptly Note: confirm engine and circuit variant by VIN First save the freeze frame. If coil G does not produce the expected primary-current signature or cylinder contribution, test ignition coil G primary feed, DME trigger line, plug well and secondary ignition components before disconnecting parts or erasing the evidence. Symptoms • The characteristic pattern is a cylinder-linked hesitation under load, rising misfire counts, spark cut and possible raw-fuel odor when the named coil is commanded. • The freeze frame is most useful when it captures that coil G does not produce the expected primary-current signature or cylinder contribution. • A graph of the affected channel beside its companion or target value exposes dropouts that a static scan misses. • Related faults should be sorted by time and module so a shared supply or mechanical cause is not mistaken for a second failure. Possible Causes Begin with accessible connections and supporting conditions, prove the component dynamically, and reserve expensive internal work for last. • Low cost: inspect terminal grip, contamination, strain and loom routing at ignition coil G primary feed, DME trigger line, plug well and secondary ignition components. • Low cost: verify the exact fuse, shared feed, ground, hose or oil path shown for the VIN instead of assuming a universal BMW layout. • Medium cost: dynamically test the named sensor, valve or actuator; decisive evidence is that coil G does not produce the expected primary-current signature or cylinder contribution. • Medium cost: correct the verified system fault, with branches including a failed coil, carbon-tracked boot, fouled spark plug, connector damage, open or shorted trigger circuit, missing feed, or DME driver damage. • High cost: consider DME repair or internal mechanical work only after circuit loading, signal comparison and the VIN-specific BMW test plan agree. Diagnosis Steps with OBDThink OBDThink is an independent BMW coding and diagnostic mobile app and is not affiliated with BMW AG. Live data and freeze frame depth depend on the vehicle, adapter and module. • 1. Scan all modules with OBDThink; save P0357, the recording DME, status, frequency, companion faults and freeze frame before clearing. • 2. Recreate the stored condition safely and graph the affected signal against its target or redundant channel. Compare coil primary behavior and cylinder rough-running data; inspect the plug well, boot and connector, then move a compatible coil only as a controlled A/B test. • 3. Inspect ignition coil G primary feed, DME trigger line, plug well and secondary ignition components; with power isolated where required, load-test supply and ground and check the signal dynamically rather than trusting continuity alone. • 4. Separate electrical from mechanical evidence by moving the harness while logging, then perform the relevant smoke, waveform, pressure, airflow, compression or oil-path test. • 5. After the proven repair, clear faults, repeat the relevant cold start or controlled drive cycle, and rescan every related module. IF coil G does not produce the expected primary-current signature or cylinder contribution AND the circuit load test fails -> repair the circuit ELSE IF the command is valid but the mechanism does not respond -> test ignition coil G primary feed, DME trigger line, plug well and secondary ignition components ELSE compare companion faults and the BMW VIN-specific test plan THEN clear, reproduce the condition, and rescan The fastest split is command versus response while testing ignition coil G primary feed, DME trigger line, plug well and secondary ignition components: a lost electrical load and a mechanically unresponsive part require different repairs. Repair • Low cost: reseat or repair the proven connector, terminal, wire, hose, ground, fuse path or oil-service error affecting ignition coil G primary feed, DME trigger line, plug well and secondary ignition components. • Medium cost: replace the confirmed sensor, valve, solenoid, coil, injector or actuator; perform only the adaptation specified for that VIN. • Medium cost: repair the demonstrated intake, EVAP, fuel, exhaust, airflow or oil-supply condition instead of masking its measurement. • High cost: repair the DME, timing hardware, cylinder head, pump or internal engine only when BMW service-data tests exclude cheaper branches. After repair, verify that coil G does not produce the expected primary-current signature or cylinder contribution no longer occurs and that P0357 stays absent as pending and confirmed through the relevant monitor. Can You Drive with P0357? Stop for a flashing warning lamp, severe shaking or raw-fuel odor because repeated misfire can overheat the catalyst. Treat P0357 as measured evidence. The saved operating condition, target-to-actual comparison and loaded circuit test identify the least costly defensible repair.